kevin gilmore

the owners of ray samuels audio will say their amp is the best. just ask them. my favorites are 1) rudistor with the silver wire enhancement 2) singlepower es2 with the all tube regulated power supply 3) felista megatron. definitely you are a moron. torus? you mean tuchas. and you must have a really big one.

100 watts maximum for those speakers!

there is (or at least should be) a board for the rk27 pot.

you may be the first person to test these boards. but if you have music, highly likely that everything works right. if the dac has a significant dc offset, that may cause trouble. maybe wiring of the pot is wrong? edit: 10k pot highly recommended with the that340 chips. 50k is not going to perform well.

so that is what new math actually is.

a short in that place is definitely going to cause trouble.

i thought the viva was all about bling.

the pictures show that the inputs are line level. and its tubes. so likely push pull transformer output. for the price, can't touch it.

I did. He confirmed it’s not a 300B output. He said the 300B isn’t powerful enough so it needed a Mosfat for the output, but I’m not really sure what that means. reference: CanJam NYC 2023 Impressions Thread (February 25-26, 2023) | Page 16 | Headphone Reviews and Discussion - Head-Fi.org so lets be specific 1) mosfet for output. lets rephrase that. 4 x apex class C high voltage power opamps. 2) 300B not powerful enough? pair of tubes is good for 18 watts. more than enough to damage your hearing. All of my tube designs that use el34 you can substitute emission labs 300b. with an adapter and extra filament transformers. Works great. plenty of power. including bh, gg, t2 and megatron. and justin's grand cayman. just because jack does not know how to correctly design amplifiers with 300b...

this is what happens if the offset pot is out of range. much easier if you have 2 voltmeters.

you need the inputs to ground or pot to zero. balance is o+ to o- offset is either to ground. repeat a couple of times.

this is how it is already done. the headphones are balanced drive only.

are you so clueless that you cannot read a datasheet. the apex opamp used in the woo is a class C device. with 450v power supply rails. so loud and horrible. the apex opamp used in the d10 is a class a/b device with 175v power supply rails. so too quiet for most people.

you cannot correctly setup this amp by measuring these voltages. you need a signal generator and a scope. leave the phase splitter adjustment alone and set the output plate voltages to about 320v. but this is only approximate. what you want for the output tubes is maximum peak to peak voltage with symmetrical clipping. what you want for the phase splitter is balanced peak to peak voltages between the 2 output tubes.

here is another koss circuit. this one seems built better.

you mean like this there was another koss circuit on ebay from a guy in ukrane, i did not save that picture. it was even worse. the soviet era toroid transformer is a real gem.

here you go pa443D

jumper connector pins 7 and 8 of the phono board connector. but really it should work fine with the board removed.

a little high voltage opamp porn

the d10 absolutely does use the pa443. same style of bent heatsink to get the heat to the case. birgir can post pictures of the d10 if he wants, and there are other pictures of the d10 with the heatsink removed. you might want to look at the datasheet, a single resistor programs the output stage bias current

pa79 mouser price is $56 each. but limited to +/-175 (its a dual opamp) i can't imagine there are any fake parts in that package so likely parts are disappearing out the wrong end of the factory. similar to the shure earbuds. mouser price on pa97 is $150 each. there are better apex parts to use in that voltage range for about the same price. you should be able to do a pair of carbon boards for the same $600, probably less. that $250 price for the portable includes the headphones. what it does not include is a lithium ion battery pack.

back board in the power supply next to the high voltage opamps has what looks to be a pair of 3 terminal regulators. one low voltgage power supply needed to drive all the input relays.

that does look like the right thing. 12au7 for gain driving 300b cathode follower. 70ma definitely pushing the tube pretty hard. not balanced.

i've been searching for over 24 hours now and cannot find a single example of a 300b used as a cathode follower. All 300b preamps seem to use an output transformer. And this completely makes sense as the voltage grid to cathode for a 300b is 75 volts. used as a cathode follower its performance has to be poor. and the opamp used for the headphones, from the apex website, this device runs class C. no output stage bias. furthermore the maximum voltage swing bandwidth is 3khz. and the slew rate is 8 volts/us. this has got to be a miserable sounding thing. there seems to be another amp just like this (for over $30k) that likely has some significant amount of solid state on the internal heatsink. 300b are great tubes when used as outputs in a push pull circuit. thats about it.

to do 10 amps you are going to need to boost the drive current. probably lowering the value of r1 to 120 ohms. same with r4.