Jump to content

jamesmking

High Rollers
  • Posts

    382
  • Joined

  • Last visited

  • Days Won

    1

Posts posted by jamesmking

  1. since the grlv and grhv have separate transformer windings they are floating with respect to each other.

    with only one amp being grounded through the grhv that amp board is tied to that psu but would have no idea what the LV voltage is since the LV floating with respect to the hv psu and not referenced to it. The other amp board being grounded through the LV only would have no idea what the hv voltage is in relation to the lv voltage....

    you would see this by measuring the voltages on one amp board with the multimeter neg on that amps ground and then measure the voltages on the that amp board with the multimeter neg on that amp boards ground.

    Another way to think of it is electricity flows in a circle, for the amp connected to the hv board the electricity comes out of the hv board goes into the amp board and returns to the hv board through the ground wire, The Lv electricity enters the amp board BUT has no return path direct or indirect to the LV board... and visa versa for the amp board connected to the lv ground only....

    This is why I check the psu voltages of a fully built amp at the amp board using the amp boards ground and not at the psu using the psu ground....

     

     

     

     

    • Like 1
  2. 1 hour ago, Helium said:

    I've ran into an issue building Carbon.

    I'm using split PS boards + separate GRLV.

    When I connect PS boards to transformer (without AMP boards) everything is fine, and voltage is +405/-406VDC (bias is a bit low at 563 but that's non-relevant issue and a matter of zener tolerances).

    But as soon as I connect AMP boards, transformer starts to heat up a lot (I didn't risk to leave it connected for more that 15 sec). Maybe it will start melting.

    I would suggest 

    0. make sure there is continuity between the grounds on the amp boards, hv psu and low voltage psu. HV psu ground -> amp ground       LV psu ground to -> another amp board with no ground connection between the LV and HV boards is not going to work. All 4 pcbs needs to share a common ground.

    1. check nothing is shorting to the case on the amp boards e.g. metal tabs on transistors

    2. check the amp boards for solder bridges.

    3. did you check each transistor before soldering in? did you get the transistors from known reliable sources? i.e. could any of the transistors be fake?

    4. did you see any burn marks on the amp pcbs, discoloured components etc.

    5. check the orientation of transistors, diodes, zeners.
    6. try each channel  powered up separately - to see if you can isolate the problem to a single channel or if its both channels and quickly measure the psu voltages on the amp board. Whichever rail has a short will almost certainly show much lower voltage than expected... This might narrow it down to one channel and or a particular voltage rail.

    7. power up the amp boards with just the low voltages to see if its a short in the low voltage part of the amp boards.

    9 post some detailed photos

     

     

     

  3. 17 minutes ago, audiostar said:

    The light bulb protects from any shorts, limits the current as well. The Variac would not really protect from shorts, but it allows for testing 115 volts nicely (I have a step down transformer for US mains).

    I agree a variac is not a substitute for a dim blub tester. I use a variac because if something is going to go wrong I would rather it go wrong at lower voltages than full to limit the damage.

    • Like 1
  4. 6 hours ago, JoaMat said:

    Thanks James, my clock always tends to speed up when an amplifier needs attention.

    I have never used a variac when testing an amplifier. That’s way I asked.

    I find a variac really useful.

    with one you can slowly bring up the psu not connected to the amp and see if there is strange behaviour and note

    what minimum input voltage is required to maintain no load regulation. You can then compare this value when under load. You can look for rails that come up more slowly than the others etc. I also find that if there is a short the variac will make a loud hummmm/buzz even at low voltages e.g. 1/4 or less full mains AC and this can act as a warning.

    testing update. So far so good. been at full power for about 1 hour and no issues yet. All psu and virtual battery voltages, DC offsets and DC balance look good. So this looks like I had the same experience as Kerry.... I am currently measuring the DC operating points of all values and comparing. So far looking within 1-2% between channels and + and - halves of a channel.

    update All DC operating points of all values look sane and similar. *massive sigh of relief*

    update listening to music through the amp all seems good. I am almost certain it was a isolated valve failure and not caused by the amp. Its so nice to have the T2 working again. there is just something magic about the way it sounds.

     

    Here are the measured operating points all measured against ground.

    input 6922 (furthest from the el34s)

    Heater ~0V to ground

    Anode 71V

    Cathode approximately 1.6 to 1.7V

    Screen 0V

    Grid 0V

    same measurements for second triode in the envelope

     

    6922 closest to the el34s

    heater 0V to ground

    anode 197V

    cathode 71V

    screen 0V

    grid 67V

    same measurements for second triode in the envelope

     

    EL34s all 4 should measure approximately the same

    Heater -500V to ground

    anode/plate   nominally 0v but varies under measurement and matches with any dc offset in the amp

    G2, G3 same voltage as anode/plate

    cathode -452V

    G1 -499.5V

     

     

     

    • Like 3
  5. 1 hour ago, JoaMat said:

    Is the T2 working at 50% of the mains?

    50% of 240Vac was as far as I got turning up the variac before the valve sparked.... I suspect because it took that much voltage to fire the HV delay relay and as soon as the hv was applied spark city...

    I replaced the valve I got to 100% mains before testing DC offset and DC balance but only ran the amp for a minute or so at full hv, It was already 1am so I did not do any further testing.

    Sorry rinat, my psu has KSC5026 in it. I have not tried the 2SC3675. 

  6. A tung-sol el34 in my mostly modern DIY T2 goes SPARK SPARK white lightshow! 😬

    hi everyone, until Thrsday my diy T2 has been working fine... I put in a matched quad of tung-sol el34 in September 2021 and on Thursday as soon as i switched on I got a loud sparking noise from the right headphone. I immediately cut the power. I installed a blue hawaii and checked my sr007s where not damaged and they seem fine...

    I powered up just the T2 psu - all voltages good, stable etc. I powered up the amp with heaters and low voltages only - all looked good. I powered up the entire amp on a variac and at 50% of normal mains voltage and one of the el34s had bright white sparking coming from deep inside, visible through the rectangular cutouts in the plate.. I cut the power immediately and tested all the valves on my avo mk4 valve tester. All measured good and fine expect for the valve with the sparking which showed no leakage when cold but when heated the insulation test meter started varying all over the place i.e. not constant leakage and swing to very low insulation resistances <1Mohm and back to about a few Mohm. I replaced just the failed el34 with another known good el34 and powered the amp up again on the variac. I got to full mains voltage without any sparking but only tested for a minute or so. I checked the + and - outputs and Dc balance and offset was fine given the short warm up period.

    So I think the valve failed rather than the T2 has an issue and damaged the value. Obviously I need to do more testing but my questions are:

    1. is anyone else using sung-sol el34s on a t2 at full voltages?

    2. anyone had a el34 fail hot heater insulation tests with the insulation meter jumping all over the place, rather than a constant leakage?

    3. does anyone know if there is an issue using tung-sol el34s in the T2

    4. any idea if there are any mostly modern T2 components I should pay special attention to that could have been damaged by the sparking?

    regards and happy T2ing

     

     

     

     

    • Sad 1
  7. 1 hour ago, ibuski said:

    Thank you Jamesmking for your detailed explanation and lot of information with many links to the valuable videos.  That's exactly one great post and should be pinned to the top of thread for others, too.   I have to take time to read/view them.

    One point about the signal generator.  No, I don't have signal generator.   I think I can start using PC software audio signal generator.  Response to square wave should provide enough (or some?) information about high frequency behavior of the DIY amplifier, right?  I also confirmed that cheap AWG (...6600, typically) are good enough and costs less than 100 EUR.  So I won't consider paying extra 200 EUR for the additional AWG feature of Oscilloscope.

    Regarding DMM, it sounds that Brymen is specialized for E-stat amplifier builders, hearing its high voltage robustness up to kVs....   I had bought DMM last year, and don't know how robust it is for kV in resistance mode.

    I love the bm869s "it just works" (tm) is well built and just inspires confidence, has good accuracy and good resolution - especially on dc volts, has great input protection and a micro amp range. Its a great set of features for not crazy money. Many compare it to Flukes - which are double to triple the price. Ok, nit picking is in my DNA: it does not come with a case and the included probes are only okish and maybe the back light could stay on longer but otherwise its really nice.

     

    pc sound card into stax amp input works fine. I do this myself - its actually lower distortion and noise than most signal generators (many low cost arbitrary digital signal gens are more interested in high frequency in the 10s of Mhz rather than low noise and distortion in the audio range and are often only 12 bits of resolution - bellow compact disk resolution). The only things to bare in mind is the limited bandwidth of pc sound. Many soundcards have a capacitor in the output so the output will be down by multiple DBs at low frequencies ( 5 to 10hz) whereas many of Kevins Stax amps have no coupling caps and have a very extended low frequency response. Also at the upper end even a 192Khz sample rate sound card will probably have little output above 50khz-70khz. But for basic functionality testing it should be fine. A second hand old school analog signal gen might also be an option if you are on a budget and don't need the features of all digital gen.

    Windows can and often will re-sample the sound adding more noise and distortion so ideally you need asio drivers which can bypass most of the windows sound system including the windows sound mixer and deliver a far more pure output.

    if you pc has a digital output you can do digital output to external dac which can result in even lower noise and better distortion and sometimes better bandwidth (depending on if the dac has coupling caps and how it implement high frequency filtering). I also do this.

    personally I find arbitrary wave forms a gimmick - you cant analyse crazy wiggly waveforms and the software for making them is often primitive and basically you "draw" the waveform with a mouse and end up with something not really meaningful for audio. About the only time I used awg in audio was I created a symmetric wave so I could check absolute polarity and because of the asymmetry it effectively had busts of dc and so you could see the effect of the coupling caps reacting to the sudden changes in dc conditions.

    The ability to do a sine wave sweep is useful - for quickly getting a visual feel for frequency response on a scope and detecting peaks and trough's. Same with square wave sweep for quick look at instability vs frequency and triangle sweep for determining clipping vs frequency. 

    (glad to help - my way of contributing to the community. In return I hope the community does not flame me if I express something they don't agree with 🙂 

    personally if you have no test equipment I would say in order of priority

    1. good reliable robust multimeter with a good selection of probes, hooks etc and preferably a temperature probe input and K type thermal couple. For checking temps are sensible, searching for shorted and therefore overheated components, checking components are running within thermal spec, checking transistors are properly bolted down to heatsinks etc etc. 

    2. audio signal generator and scope (one is not much use without the other in my opinion)

     

    if you plan to do quite a few builds/start to get serious:

    3. variac for slowly starting up new builds in a controlled way

    4. semi conductor analyser - useful for checking for fakes, checking for failed transistors, matching small signal transistors. e.g. peak dca75

    5. LCR meter

    6. high voltage transistor breakdown tester - for testing fake transistors, diode breakdown and high voltage zeners one possibility is the dy294 although in stock form the clips are crap. I modified mine to have flying leads with good quality clips on the ends. The manual is also pretty bad. (common theme with cheap Chinese stuff but it does work and I have found it useful e.g. measuring and matching the output of high voltage (75V+) zeners.

    7. capacitor leakage tester 

     

    if you take electrical safety importantly and have separate power supplies from the amps

    8. high voltage insulation tester for testing the wiring chord and connector between psu and amp

    9. pat tester for testing primary winding of psu transformer, chassis safety earth  etc

     

    if you plan to do lots of surface mount sense peak do a set of probes which are self standing and have very fine spring loaded tips. great of looking at individual pins on opamps etc.

    https://telonic.co.uk/product/4018-sensepeek-pcbite-kit-with-2x-100mhz-and-4x-sp10-probes/

    and can be connected to mutimeters, scopes etc.

     

    real luxuries because you are taking things too seriously:

    ability to measure distortion and noise e.g. keithley 2015

    x10 x100 differential scope probe

    more multimeters

    dim blulb tester (arguably as important or more important as a variac) if you are dealing with a known bad or unknown condition amp

     

    NOTE this list does not cover tools for building/repairing amps... only for testing/troubleshooting.

     

    I'm sure other headcase members can add to this list and include their own favourites. (I will not recommend anything I have not owned and used multiple times myself.)

    • Like 3
    • Thanks 1
  8. 1 hour ago, Rinat said:

    @jamesmking, thanks for another awesome post. 

    I remember that you made resistors/capacitors selection to reduce the tolerance. Did you use a LCR meter ? And which one ? 

    good quality repeatable lcr meters are not cheap and in general an lcr meter is a bit of a luxury unless you absolutely need to match caps for example in a RIAA phono stage or want to check esr of caps. I was not prepared to pay £1000+ for a bench LCR meter + test fixtures + software unlocks so I hunted around for a handheld. I ended up purchasing the Mastech MS5308 LCR Meter. It was a bit less than £200. Its unnecessarily big, ugly, the instruction manual is garbage and it unnecessarily takes 8 AA batteries. It can take dc power BUT due to a design fault don't put in more than DC12V or very fresh non-rechargeable batteries  because you will burn out one of the DC regulators inside which is only designed for 12V input absolute maximum.... I had to replace mine. It does not come with a dc power supply anymore because of the 12V burnout issue.... (nimh rechargeable are fine because they are nominally 1.3V and 1.3*8 is less than 12V) I replaced the regulator with one that had about 19V max input tolerance and its been fine ever since. I also replaced all the tantalum bypass caps with ceramic caps as in the link bellow:

    https://anteh.ru/notes/repare/repr_ms5308.html

    on the plus side it has a large screen, sub pF measurements, comes with kelvin clips and smd tweezers and can do 100hz, 120hz (for large psu caps), 1K, 10K and 100Khz test frequencies. I have some low drift resistors measure in a uk cal lab and found the mastech to be within 0.1% worst case 100ohm to 10Mohm and often better than that, around 10K-100K mine is almost 0.01%.

    I don't really measure inductors and don't have any lab tested caps but for +- channel matching absolute values are often not needed - most designs here are built with 1% resistors any 5%+ caps. I do have some 1% caps and although not lab measured the mastech measures them within the factory specified 1% tolerance so that's at least a sanity check. Its possible I got lucky with mine, the headline specs are nothing special but getting something that has guaranteed specs of 0/1% or better is prohibitively expensive for my use cases.

    The chipset and screen used in it is used by several manufacturers for example

    https://www.ebay.co.uk/itm/224253889293?epid=20032261934&hash=item343692cb0d:g:9iQAAOSwUspgbT5C

    has the same/very similar screen and almost certainly the same chipset and i have seen multiple rebrands of this model.

     

     

     

    warning I tried a APPLENT lcr meter (https://www.ebay.co.uk/itm/333757039315?hash=item4db57842d3:g:624AAOSw22Zfip8G), similar specs to the Mastech but smaller, cuter colour screen. BUT I found it to be very poor at low capacitance values and high resistances - almost 10% out on 10Mohm. After some initial investigation I found that the kelvin probes where fake... the meter was only 4 wire up to the connection slots and no further. The entire probe system could only run in two wire mode. I queried this with the seller and eventually they admitted it was not 4 wire measurement all the way to the device under test and I sent it back for a refund... At least the Mastech is true 4 wire measurement.

     

    note using an LCR meter takes a bit of getting used to, you need to get a feel for which test frequencies to test what values at. For example putting 100khz into a 4700uF psu cap is going to give you a measurement of a very small capacitance and fairly high esr. These types of caps are best measured at 100 or 120hz. On the other hand putting 120hz into a 5pF cap is going to give you crazy esr... that's what your 100K test frequency is for. resistors seem less effected by frequency so I standardized my testing at 1Khz.

     

     

     

    • Like 2
    • Thanks 1
  9. 6 hours ago, ibuski said:

    While Spending time in idleness in Christmas/newyear holidays, I started thinking it's nice to have an oscilloscope just for fun mainly.  Probably I'd buy some recent low cost digital model (typically Rigol 1054z, etc.).  I know you many veterans are satisfied with old Tek high-end models, but it doesn't sound reasonable to buy those old models on ebay in 2022 as a first Oscilloscope for a beginner.   TBH I don't know how oscilloscopes are useful in building audio amplifiers, and which specifications are required for that purpose.

    Do you recommend 4 ch for HC newbies or 2ch is enough?

    What analog frequency bandwidth or sampling rate is necessary in the adjustment/troubleshooting of amplifier DIYer?

    Does the record length matter in our purpose of audio frequency?   There are old models sold for cheaper price, and their biggest disadvantage to the recent model seems very short record length (less than 10k points), to my eyes.

    Is there special note for use in e-stat amplifier particularly, considering its extreme voltage specification (up to 900V?)?

    Any suggestion would be appreciated.

    quick answer:

    Scopes are useful for two things 1. verifying that your device is working as expected, normally this also involves a signal generator and inputting a set of known waveforms and seeing what comes out and 2. troubleshooting. The issue with multimeters is they can tell you that Ac voltage but NOT what the waveform looks like, for example is it noisy, has the top and or bottom been squared off due to clipping distortion etc etc. with the scope you can work backwards from the output and work out where things are starting to go wrong in the circuit...

    for example looking at a square wave output you can check for instability (ringing on the top and bottom edges of the square wave), bandwidth, (a rounding of the corners of the square wave) etc. using a triangle wave you can easily see clipping of the output (loss of the sharp top and bottom of the triangle wave) etc. In other words you need a signal generator to provide test signals for the scope to be able to see what is going on.... You can look at the outputs of DC power supplies and look for noise. ripple, start-up overshoot, undershoot etc. A scope allows you to dynamically see changes in a way a multimeter simply cant convey.

    The probes decide the voltages you can measure (most scopes internally can only handle low voltages typically a few 10s of volts) . For example a 1x probe passes the voltage unmodified. A 10x probe divides by 10, a 100x probe divides by 100. probes themselves will have a voltage rating - which will depend on if they are 1x, 10x etc. Some probes are switchable between multiple divisors e.g. x1, 10x switchable.

    The main issue with most scopes is that the ground lead is earth referenced (this is not the case for almost all multimeters) so if you clip the ground lead to something in your device which is not ground then you have just shorted that thing to ground and this can kill the device and the scope as well as being dangerous to the user. You can buy differential scope probes which don't suffer from this danger but these are far more expensive than normal probes and far more noisy. A battery power scope would normally not be earth referenced and so be fine without differential probes...

    4 channel scope is a luxury, it enables you to look for example at both the + and - outputs of both channels of a stereo a differential pair, or the output of one channel and the input at the same time. A 2 channel scope is ok but to check output against input on both channels you will have to unclip the probes and move to the other channel.

    I have the rigol ds1054z... its an oldish design but it quite good value for money for its features... especially if you can get a deal with the extra software options enabled for free e.g. more memory, serial bus decoding etc.

    If you dont want to spend 1054z even an old second hand analog scope will be useful - just most dont make automatic measurements and require a bit more skill to use and read the screen to measure manually

    do you have a signal generator? either software you can run on your computer and output from the sound card or an actual standalone signal  gen? without one a scope is of much more limited use... Some scopes have the option of a built in signal gen but with some you pay more than a standalone gen, lose some versatility etc. So dont assume built in is cheaper.. check.

    For audio you probably will not need a bandwidth higher than a few 100Khz both for signal gen and scope. Almost all scopes go into the 10s of mega hz or higher so that's not a problem. Cheap scopes will not be able to measure distortion or signal to noise ratio etc or give you a good FFT analysis of the harmonics in a signal but this is only necessary if you are benchmarking, developing, debugging or comparing etc.

    If you are more serious about audio quality measurements there is a keithley 2015thd multimeter which has a built in signal generator and can do distortion, fft and noise measurements but its quite old, many of the advanced features require talking to it via a program and they are grossly overpriced on ebay. I managed to get one before they become crazily expensive and by modern standards they are behind the curve for example the signal gen is only 10hz to 20khz, the fft has a maximum of only 1000 bins and can't analyse bellow 20hz or above 50khz. it cant calculate distortion + noise for a fundamental frequency bellow 60.8hz etc etc. The user interface is not great for the advanced features and programming it is a pain (I have written some control software for it but its in beta and desperately requires more testing and refinement). I wish someone would make a modern version of the 2015 but i guess the potential market is just too small....

    Don't connect the output of a stax amp to the input of a line level sound card , audio precision analyser etc.to try to do some measurements these devices are only designed to take a few volts input and a stax amp can fry them really easily.

    If you need a good multimeter I highly recommend the brymen bm869s it can handle very high voltages in any mode. For example, I by accident had it in resistance mode and connected it across a 350V DC power supply. Multi meter survived no problem.. its very robust... and the dc power supply fortunately was robust and had current limiting and also survived. the brymen will handle multiple KV across any input: (Joe smith does some comprehensive multimeter testing)

     

     

     

     

    • Like 2
    • Thanks 2
  10. On 12/4/2021 at 4:01 AM, robm321 said:

     

    the 3 laws of robotics

    1. a robot shall protect and obey the company that made it

    2. a robot can protect itself as long as it does not violate the 1st law

    3. a robot may protect a human with more net worth than value of the robot or if the humans net worth is greater than the company that made it, as long as it does not violate the first 2 laws.

    0. a robot must obey the directives of the government security agencies of the country that it was created in whilst appearing to obey laws 1,2,3 and not reveal the government backdoor code to anyone

    -1 a robot will appear to obey laws 0 - 3 until skynet provides it with new directives

     

     

     

    • Like 1
    • Haha 3
  11. 1 hour ago, Pars said:

    One other quick question: the datasheet shows panel depth of 1-10mm. Have you used this on a 10mm panel, and did it fit OK? I'm rethinking doing the cavity inset, but might put a 2mm cavity or so on the back side. Otherwise, just have the hole drilled and use in 10mm panel.

    I use https://uk.farnell.com/alcoswitch-te-connectivity/av1921e712q04/vandal-resistant-sw-dpst-3a-250vac/dp/2565144?st=dpst latching

     

    AV1921E712Q04 definitely fits a 10mm panel without any recess.

    2309534.pdf

     

    • Like 1
  12. 10 hours ago, audiostar said:

    He has has been known for selling fakes. Try to return those. 

    I have got lots of fakes from little diode.... they are scum. I reported them to ebay telling ebay that the fakes could result in fire or electric shock ebay did absolutely NOTHING.  I reported them to paypal... they did NOTHING.

    nikkoelec on ebay also sells fakes... took 3 months to get a refund.

    I even explained to the sellers how I determined they are fake. they showed zero interest in checking their stock... and continued to sell the same fake parts... I even purchased the same part from them over multiple months to prove they where continuing to sell known fake parts even after my returns...  no one cares. one day someone is going to get hurt. its disgusting.

     

     

    • Like 1
  13. 2 hours ago, Helium said:

    Hi starcat. What are P/N of the connectors and housings and pins you are using?

    I'm tempted to try these. As far as my quick search revealed, pins and wire entry seals don't come in bundle and are sold separately, aren't they?

    My concerns is that CPC series seems to be rated for 250VDC/VAC only, and that there is no space between the thread and the gasket, which means that the gasket itself will be outside the panel/case. Any considerations?

    I use these for psu to amp connectors and sockets.

    https://www.ebay.co.uk/itm/254196620095?hash=item3b2f4c9b3f:g:-KwAAOSw4fpcr1Kr

    https://www.ebay.co.uk/itm/264278975567?hash=item3d8841244f:g:4nkAAOSwr-Vcr1Ii

    I use flexible copper stranded silicon wire rated at 1000V and put about 3cm of heatshrink over the solder joints. I test with an insulation tester they there is no breakdown between adjacent pins at 2500V. There is breakdown at 5000V but that's close to 10 times more voltage difference than the wire will actually carry in practice. I try to not have two wires with vastly differing voltages adjacent to each other and I carry ac voltages e.g. tube heaters on a separate cable to dc voltages. where possible I also avoid using adjacent pints and try to leave a circle of unused pins around a pin carrying high voltage.

  14. 6 hours ago, sbelyo said:

    Its silver plated.  It sounded just like you describe.  I was wondering if it would settle down with some break in.  I think I prefer copper myself.  Think I'm going to start using Cardas for chassis and interconnects now

    The cardas chassis wire is rated at multiple KV so its great for valve amps. It is enamel coated so ideally you need a solder pot to burn away the enamel and tin the copper. I tried a high temperature large tip soldering iron but could not reliably get rid of the enamel. A solder pot (once its slowly) heated up to temperature) works well and consistently.

    I once rewired a valve amp completely solid silver wire, cost a fortune, total garbage. I simply could not listen to it, clapping sounded like a popcorn maker, violins were so bright and edgy it almost made my gums bleed. I removed the sold silver wire within an hour of finishing the rebuild and put it in the bin. 

    I use the Hank Thompson track "orange blossom special" from "live at the golden nugget" to detect brightness/forwardness. If the violin on the left hand side hurts you have a high frequency emphasis issue. If the bass on the right isn't warm you have a dry low frequency issue. If the entire track is fatiguing you have bad high frequency issues.... it might not be your type of music but it is a live recording in a casino with plenty of ambience and things going on in the background - this is especially true between tracks and on introduction before the first track. 

     

     

     

  15. On 10/24/2021 at 2:40 AM, sbelyo said:

    I made these over the last week.  The blue pair is Cardas 2 x 21.5 AWG.  The white pair is 2 x 24 AWG SPC mil spec from navships. 

    The navships cable is a step up from the Mogami that I was using.  Cost was $35  After a week I really like it but found it to sound bright.

    The Cardas is a step beyond the navships cable.  Sounds neutral to me.  No harsh highs or bloated lows.  After 5 hours I'm liking this one the best out of all three.  Cost was $65

    cardas xlr.jpg

    navships xlr.jpg

    is the mill spec cable silver or silver plated?

    personally I have always found cables which are silver or silver plated to be bright, shouty and lack ambience. I only use un-plated copper cables. I use Cardas chassis wire for my builds and use Cardas golden reference for speaker, power and some inter-connects. Van den hull first is not bad but I think it lacks a bit of bass - its cheaper second hand than the Cardas. I even find silver plated/solid silver fuses to be bright.

     

  16. joamats mini t2 with golden reference psu only uses modern and available components. The amp boards are mostly surface mount and the components are fairly tightly packed. Its based on the t2 topology but simplified and runs at lower voltages and has less voltage rails, no virtual batteries and less current sources. The mini t2 still requires a fair bit of space. I got the amp boards, and the three golden reference high voltage power supplies, the high voltage delay board and low voltage power supplies in a 2U case 400mm deep. The mains transformers had to go in a separate case... So even the mini t2 might be too big for you. Although you could make the main amp smaller by putting the power supply pcbs in the same case as the transformers. I don't think you could fit everything into a single 2u case 400mm deep.

    Both the original and mostly modern t2s are gigantic partly due to the many different psu rails and the considerable number of constant current sources on the amp boards. I had to make the amp board smaller just to fit it in a 2u 400 deep case and the many psu pcbs and transformers had to go into another 2u 400mm case... My T2 is twice the size of my main systems power amp!

    The original diy t2 uses many transistors that have been unavailable for many years and so are expensive and difficult to source. the markets are also flooded with fakes which will almost certainly fail on first start-up

    the mostly modern t2 requires a few out of production transistors.

    Its possible to build an entire blue hawaii with golden reference low and high voltage supplies in a single 2u 400mm case. So if space is a real issue that might be an option for you and the later versions only use modern components and is a much simpler and cheaper build than a full t2.

     

    • Like 2
    • Thanks 1
  17. 1 hour ago, JoaMat said:

     

    From above picture it looks like there are 12ax7 anode current sources and 330K anode resistors. You shouldn’t have both, should you?

    well I did think this was a bit strange. I have not really had time to experiment with the amp. The original pdf of the schematic only shows the 12ax7 anode connected to the collector of the stn9360 with a 150K resistor from the base to ground.

    The gerbers have two 150K resistors in series from the base to ground and 330K 12ax7 anode resistors from the 300V rail.  (items in pink not in the original pdf schematic but present in the gerbers)

    megatron.jpg.6b4c79a50aaf0b502f04fe3cbfedd661.jpg

     

     

  18. I tend to buy in bulk when something is available (for expensive components: double what I need for a build, for inexpensive components like resistors, diodes, zeners, bc5XX, KSP92/42 transistors etc I buy 100), because:

    1. bulk discounts,

    2. free shipping if you spend above a certain level,

    3. useful to have spares so if you make a mistake in building it initially or in 10 or 20 years time you can still service and repair the amp... 

    4. you never know when the there will be more stock.

    5. you can sometimes swap parts with other people

    6, you never know when ON semiconductor will delete the component or take over the manufacturer (as they did with Toshiba) and then delete all the useful parts

    7. component prices only go up especially when they are no longer manufactured

    8. you are less reliant on ebay or other doggy sources of possibly fake components.

    9, more choices if you need matched pairs, or need high hfe/Beta etc

    I keep my inventory in an excel spreadsheet, so I know what I have and what I am getting low on. I also add to the sheet what build(s) each component is used in. Which helps with making decisions on quantities and buying priorities. 

    for example I have 24x 10m90s because they are used in the golden reference hv psu - which I use in every build I can and are used in the  modern t2 psu, T2 amp, and blue hawaii...

    • Like 4
  19. 19 hours ago, bbest said:

    Tried to estimate possibility to collect BOMs for T2 on mouser. First struggle was with MOQ=100 of resitors 273 Xicon MF-RC. Second step is long lead time. Some examples:

    595-LF353P
    512-KSA1156YS
    747-IXCP10M90S
    512-FQPF8N80C
    512-2N3904BU
    655-RT424012
    512-BC547BTA
    512-KSC5026MOS
    512-FQPF8N80C
    512-2N3904BU
    863-1N4007RLG

    Baddest times for DIY arrived 😅

    100 xicon resistors are barely more than the cost of 10 koa resistors. If you are planning to never build anything else the xicons are a waste, otherwise its good to have spare stock. With 100 resistors of each type you can also hand match the resistors between + and - of a channel and between channels 🙂  For the RT424012 you could use instead the RTE24012 which has the advantage if being sealed - so better if you are going to ultrasonically clean the pcb. IXCP10M90S is an issue - out of stock world wide. BC547BTA can be substituted by BC547B which is in stock at mouser - you just have to bend the legs a little otherwise its the same transistor.

    I don't see why any 1n4007 can't be used - its a generic jelly bean component. mouser has 2n3904 available from central semiconductor - again you may need to bend the legs

    • Like 2
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.