Jump to content

The Multi Amp aka Dynalo Mk2


spritzer

Recommended Posts

Same number of output devices (8 per +/- channel, or 16 per L/R channel). Mini uses 16 PZTA06/56 and 6 MMBTA06/56. Full uses 22 MPSW06/56 (thru-hole, not available anymore), or 22 PZTA06/56 (16 output, 6 biasing/VAS) for the SMT version (current). I don't see a schematic for this version (the thru-hole schematic is still on Kevin's site).

Link to comment
Share on other sites

2 minutes ago, Pars said:

Same number of output devices (8 per +/- channel, or 16 per L/R channel). Mini uses 16 PZTA06/56 and 6 MMBTA06/56. Full uses 22 MPSW06/56 (thru-hole, not available anymore), or 22 PZTA06/56 (16 output, 6 biasing/VAS) for the SMT version (current). I don't see a schematic for this version (the thru-hole schematic is still on Kevin's site).

 

page 33

Link to comment
Share on other sites

On 17.12.2016 at 5:56 PM, Kerry said:

Here are the schematics:

 

SSDynalo-v1-5-Amp.jpgSSDynalo-v1-5-Channel.jpgSSDynalo-v1-5-PS.jpg

 

I've got to look up the settings again for the positive rail. I'm running out in a bit so may need to do it later.

EDIT:  Ok so the silk screen should read 14.2V before you start bridging the jumpers.  You should bridge 3P2V, 1P6V, 0P8V, 0P2V for a 20V output.

Also, updated schematics to make them higher resolution.

 
SuperSymmetryDynalo-v1-5.zip

 kgdynalobal9.zip

These are the 2 I am referring to.
These pictures are for the SuperSymmetryDynalo-v1-5.zip version which as far as I know is the mini.

I didn't look into the  (dynalobalXX.zip) at all since they seem a bit older.

I might have to reread the whole blog :unsure: and write down some sort of version control for everything.

Link to comment
Share on other sites

Yes, that is the mini. The kgdynalobal9 is the full size, but is also SMT for most of it. Use with the GRLV (or Amb sigma22, etc.) PSUs, normally at +/-20V.

The kgdynalobal files seem to use SMT transistors, but thru-hole resistors. These are all full size; I'm not sure which is considered to be the latest. The kgdynalobal9.zip  was what was used for the recent group buy, here.

  6/5/2015  9:49 AM       242761 kgdynalobal5.zip
 11/2/2016 11:09 AM         4298 kgdynalobal9.PKP
  2/6/2016  8:25 AM       325771 kgdynalobal9.zip
11/13/2016  6:34 AM        88083 kgdynalobal9g.zip
11/12/2016  4:20 PM        79877 kgdynalobal9G2.zip
 6/23/2015  6:59 AM       237220 dynalobal12.zip
 6/23/2015  6:59 AM       235328 dynalobal13.zip
 6/25/2015  4:22 AM       236564 dynalobal15.zip
 6/25/2015  4:22 AM       252016 dynalobal17.zip
Link to comment
Share on other sites

52 minutes ago, cspirou said:

So biasing/VAS is certainly different between the two. Is this why the mini version needed heatsinks for the output transistors?

No.  The bias/VAS, etc. are the same.  There are some slight value differences in the biasing resistors (accounted for in the BOM), but that's because the LEDs have different forward voltages so the resistors need to be adjusted.

Edited by Kerry
Link to comment
Share on other sites

2 hours ago, Pars said:

Schematic for the SMT SS Dynalo, not the mini.

So the Schematic is for the mini? And the SMT SS Dynalo board (dynalobalXX.zip) is outdated?

It's good to know that there is a version called SMT but if it's redundant. 

Link to comment
Share on other sites

Kerrys awesome mini will fit a FPE profile 1 enclosure.
The smallest I could get it: 133.92mm (W) x 172.72mm (D) x 42mm (H)

Smaller than Cavalli’s Liquid Carbon in height and depth, and only slightly wider by 6mm.
Cavalli’s Liquid Carbon = 127mm (W) x 178mm (D) x 45mm (H)

I get my panels next week, I can’t wait to see how it turns out! Here are the drawings.

33205037081_120d5daade_h.jpg

Will share if anyone’s interested :D.

Edited by johnwmclean
  • Like 14
Link to comment
Share on other sites

Well that was very quick shipping from FPE :),

Initially I was going for an all out black box, but FPE don’t do anodising after milling leaving the panels with silver edges, which got me thinking silver sides would help blend in more naturally, so that’s what I did.

I’m really happy with the result overall, the fit is really good, the side edges and base of board have have good clearances. I’m still waiting on feet, final LED and volume knob. I’ll do some testing and see how I go with the temperature, uncased I was getting around ~65° over the regs, THATs and outputs, I may have to turn it down a little, depending...

33415316665_f2ac836d1a_h.jpg

32572727344_a7128234b7_h.jpg

33374957906_fca720a8c3_h.jpg

 

Here are the FPE files;

https://akashare.egnyte.com/dl/PjWB17863x

The side panels are profile 1 cut to a length of 172.7mm.

 

Edited by johnwmclean
  • Like 14
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.