Jump to content

current feedback electrostatic amp


kevin gilmore
 Share

Recommended Posts

On 7/10/2018 at 10:45 PM, mwl168 said:

This is a great sounding amp. For the parts cost (when you can get them), this ES CFA probably takes the crown of the ROI of all the ES amps I have built.

So Glad you like it. never sure what someone else will think / hear

its a  good thing I did not build this first

might have found an even more expensive hobby

Link to comment
Share on other sites

  • 1 month later...
58 minutes ago, Laowei said:

FYI,

PBHV9560, PBHV8560, KSA1156 are all in-stock at Mouser and shipping.

KSA2752 are still BO until November.

Kevin has noted that KSC5026 is a substitute for KSC2752. Last I checked it was BO at Mouser but in stock at Digikey!

Edited by mwl168
Link to comment
Share on other sites

54 minutes ago, mwl168 said:

Kevin has noted that KSC5026 is a substitute for KSC2752. Last I checked it was BO at Mouser but in stock at Digikey!

Thanks. I’ll give Digikey my order. Looks like I’ll have all the parts to try the little amp out. I’ll repurpose the PS from my KGST to power it.

56 minutes ago, congo5 said:

Yes, have made boards from those gerber's and they work just fine.

when I last ordered some (19-Oct-2017) it said Jan 2018

Thanks for the resistor confirmation. The BO slide on that BJT is not too encouraging... 

Link to comment
Share on other sites

  • 3 weeks later...
  • 2 months later...
  • 1 month later...
32 minutes ago, Pars said:

I thought it was either the Xicon 271 or 273 series resistors that we’re used for the electrostatic amps? I could be wrong/behind the times...


Sent from my iPhone using Tapatalk

The problem with Xicon is max volt: 

350v max (271 series), 500v max (294 series) vs 700v max (Koa MF1 series 1/2w).

Edit: I'm reviewing the technical sheets and I see that the data is similar for both the Xicon (293 series) and the KOA (CF1). All my BOMs are with KOA resistors 

 

Edited by jose
add dates
Link to comment
Share on other sites

Koa 1/2W (MF series IIRC) and RD60 should be fine in most positions with Electrostatic amps. I’ve used both without issues.

From what I read, the Xicon is better for the battery positions in Kevin’s T2 - others seem to result in noise issues likely due to leakage.

Edited by mwl168
Link to comment
Share on other sites

 I haven´t predilection for any particular resistors brand. I use what works but if there are better ones for these amplifiers, I'll buy them of course.

For terminal I think we all use the same Phoenix (MKDSN series).

 

 

 

 

Link to comment
Share on other sites

18 hours ago, jose said:

For terminal I think we all use the same Phoenix (MKDSN series).

I measured the pin spacing on the boards as well as the BH Ultramini PSU.  They're all 5.08mm  The MKDSN series are all 7.62mm

It doesn't look like they'll fit and I don't see anything in that size higher than 300V

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...