HatIsMyFriend
Members-
Posts
9 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Everything posted by HatIsMyFriend
-
Kerry Design mini GRHV\GRLV and JoaMat mini T2 Group Buy
HatIsMyFriend replied to mwl168's topic in Do It Yourself
Got the boards this morning, thanks a lot! -
Kerry Design mini GRHV\GRLV and JoaMat mini T2 Group Buy
HatIsMyFriend replied to mwl168's topic in Do It Yourself
Great to see them arrive well. I read a lot of horrifying things about Fedex in the US, but strangely enough, they're pretty much the best of the bunch where I am. I consistently have them arrive full days in advanced, or have packages sitting at their warehouse waiting for delivery day, and I can get them to deliver much earlier if that's the case. The local postal service, on the other hand, loses packages by delivering it to another address, stuck onto the bottom of another package. Of the same shape and size. -
Kerry Design mini GRHV\GRLV and JoaMat mini T2 Group Buy
HatIsMyFriend replied to mwl168's topic in Do It Yourself
Since the mini T2 boards seem to be correctly at 2mm, I don't think board flex will be a problem when changing tubes around. I'm fine with 1.6mm for the PSU. -
Kerry Design mini GRHV\GRLV and JoaMat mini T2 Group Buy
HatIsMyFriend replied to mwl168's topic in Do It Yourself
Paid. -
Kerry Design mini GRHV\GRLV and JoaMat mini T2 Group Buy
HatIsMyFriend replied to mwl168's topic in Do It Yourself
I'm still in. Thanks for organising all this, by the way! -
Kerry Design mini GRHV\GRLV and JoaMat mini T2 Group Buy
HatIsMyFriend replied to mwl168's topic in Do It Yourself
Bare boards please. Also, add the following to my order: +1 GRLV78 +1 GRLV79 +2 GRHVxxx Thanks! -
Kerry Design mini GRHV\GRLV and JoaMat mini T2 Group Buy
HatIsMyFriend replied to mwl168's topic in Do It Yourself
I don't mind either way. If it's assembled though, would the voltage setting resistors be left blank for flexibility, or would it be set to +400 -460? -
goldenreference low voltage power supply
HatIsMyFriend replied to kevin gilmore's topic in Do It Yourself
Hi, I've a few questions regarding the mini GRHV/LV, if this is the right thread to ask in. 1. Since the base board only has a single cap per unregulated voltage, I suppose the highest voltage secondaries for the HV section that can be used is 350VAC? Around 90% of a 550VDC cap's rating? Assuming that is the highest voltage rating I can get on a 680uF board, which it should. 2. Is there a BOM for the base board? Have been comparing the diagram with the GRHV and LV and figured out most of it, but not quite sure if I got it right, especially the delay circuit. Found another diagram here on it, but it was on 12V rather than 5V, and I'm not sure if the relays would even open on 5V with the same values. 3. And, lastly, what's the trimmer R21 for? Bias adjustment, I assume? It's not on the GRHV boards, or I'm blind and/or looking at the wrong ones. It's a lot to ask for so, thanks for reading! -
Kerry Design mini GRHV\GRLV and JoaMat mini T2 Group Buy
HatIsMyFriend replied to mwl168's topic in Do It Yourself
A full set, if not too late: 2 * GRHVxxx 1 * GRLV78xx 1 * GRLV79xx 1 * main board 1 * Mini T2 board Thank you!