kevin gilmore

boards actually fit. well shit.

https://drive.google.com/drive/folders/1r3g2TAtBUaBdiMorTWX7yYgeJ7maQbYW?usp=sharing

https://drive.google.com/drive/folders/0B7egryukiT7_TFlEQlBRejdVdDQ?resourcekey=0-nGWwBYQ_Uivj-ciBLYMeaA&usp=sharing

you probably want to find and use my protection circuit. less parts. and also does balanced if needed

gz34

boards and transformers ordered.

i think i fixed it, someone test please.

yep that sounds about right. The resistance of the inductor is 100 ohms.

636v center tapped transformer dual tube diode, 220uf to ground 5H inductor 2 x 220uf to ground. The turn on thump puts about 700v on the first cap. which is why the caps blow up. adding 50 ohms after the diodes softens the bump. whats the best way to calculate the required primary voltage for 400v at 100ma dc output.

do no replace these parts. buy from someone that has them or wait.

So this is what its going to look like when its done. And Hammond is willing to do the custom transformers. With a price that matches the complexity. Anyone with experience with tube rectifier power supplies driving 5 Henry inductors?

hey joamat wanna make a couple of test boards before real money is spent?

joamats hand made boards look much better than that. posted latest schematic. Does anyone recognize the tube power supply? And the output tube has 300v cathode to filament on a tube rated at 100v. Does (did) it even work? birgir mentioned this earlier. have a look Image-Hifi.com-62015-Viva-Audio-Solista.pdf (audiograffiti.com) so lots of very high voltages, lots of heat and flammable felt and a horrible point to point job. But wait, there is more, my good friend ray samuels and his A10. 5687 output tubes in srpp configuration running with a plate voltage of 500v. So at peak output voltages the cathode of the top tube sees 500 volts with respect to the cathode on a tube rated at 100v. How does this even work? megatronschem2.PDF

the biggest problem is that the tube sockets are up to .02 inch off in both x and y. really hard to make a circuit board with tube sockets fit into the holes with a top panel that is .35 inch thick. and all the blind holes for the other board mountings were hand tapped and then the holes in the boards were made bigger till it fit. this is so hopelessly fucked. might have to make the holes in the tube sockets much bigger to allow for the slop. No room for a regulated power supply. do want to know how the dremel tool work was done. also corrosion all over the place when the electrolytics let loose. at least we finally have an example that is much worse than the singlepower es2. not sure how to continue.

the input wiring is monster cable magnetically shielded cable. Says so right on the cable. And it was a quad balanced pot wired as unbalanced.

bias circuit DO NOT DO THIS!!! megatronschem2.PDF

back of circuit board. look at that filament wiring. and the corners notched out of the board. bias board. its even worse, after the 100k resistor 2 x .022uf caps to ground tied directly to the headphones.

So i figured that i would test the 300v supply to see if its worth saving. But no, BOTH transformers are < 1 ohm on the primary. But no way was i expecting this. And the bias resistor for the headphones really is 100k. Very bad for the headphones. A voltage multiplier *7 from 90v. unregulated, no zeners, no protection, no anything. But wait there is more, hand made circuit boards with a dremel tool. This all has to go. But wait, the first picture is a regulated power suppy whose sole job is to drive the power led in the switch.

its here filament transformer for sure smoked. as in hole in the potting likely where the flames were shooting out. has that wonderful singlepower extreme smell. If anyone knows where to get transformers like this made, let me know. specs are as follows. Filament transformer, mounting holes 85mm square threaded with 4.5mm bolts 4 x 6.3 volt at 2 amp 2 x 6.3 volt at 4 amp 1 x 12.6 volt at 1 amp 18 volts @ 1 amp Primary 2 x 115vac High voltage transformer, mounting holes 100mm square threaded with 4.5mm bolts Primary 2 x 115vac 2 x 5 volt at 2 amp 2 x 630volt center tapped at 200ma 510 volt center tapped at 130ma 6.3 volt at 1 amp So many bad solder joints. grounding shields on the small tube sockets essentially force removed with a side cutter. Yikes. Notice the required missing corner out of the new board. Fucking idiot made the case first then found a way to cram everything inside.

https://drive.google.com/drive/folders/1r3g2TAtBUaBdiMorTWX7yYgeJ7maQbYW?usp=sharing new link, files uploading includes all new zip files published since the first upload.

does not work for me either. that google drive is birgirs i think lucky i have all of this backed up in many different locations

a quick game than anyone other than birgir or orientexpedite can play. look at the amp board above. now look at some of the other pictures of the real amp board. anyone know the 4 required major components that are missing? First one gets 10 booby points. hint: https://www.head-case.org/forums/topic/10783-megatron-electrostatic-headphone-amplifier/?do=findComment&comment=551186

stax mafia electrostatic portable in the works. would need the bias adjusted for the shure headphones.

files in the stax mafia google shares.

The output stage at least is definitely megatron. DC coupled with tube current source driving a gain tube. The rest of it has significant changes, why i don't know.