Kerry
-
Posts
2,286 -
Joined
-
Last visited
-
Days Won
12
Content Type
Profiles
Forums
Events
Posts posted by Kerry
-
-
SMD version of the CFA3 dynamic
-
2
-
1
-
-
You’re hired 😄
-
1
-
1
-
4
-
-
Yes. Typo. Food coma
-
For D24, most people used LTL-4213 on the original builds.
In the active batteries, I use a 7V reference and set the current down to .00093mA (3x 260k resistors). That puts about .23W on each resistor.
You’d need to adjust the sum of R31, R32 to 14.7k
If you’re planning on doing this, I can double check the values.
-
Thanks. I think I'll pick one up.
I've had the amp playing from 9:00 this morning (did I mention it really sounds great
) and batteries were down to 9.8V at 3:20PM. They are not perfectly balanced so one battery is at 3.1V which is below the minimum 3.3V recommended. So looks like I'm getting a little over six hours with these batteries (3x2000mAH). I can look for larger batteries and also play with some optimizations. I've also been running additional 5V and 3.3V supplies for the DAC that consume extra power. They're not needed for just the analog input.
The balancer should have kicked in to turn off the battery pack, but it didn't. I suppose it would have at some point, but I plugged it back in to charge. I have a different and smaller balancer that I'm going to try. Maybe that will do a better job.
-
8
-
-
Some more good progress. The amp is up and running
I've got two issues on the board, but the amp, power supplies and USB-C PD / battery management are all working great.
The wires going to the pot are temporary. There'll be a board for the analog/DAC inputs. The PD chips are small with lots of pins on them. I'm surprised I could solder them
Lots of 0402 chips on the right side of the board...
Here's the amp running with the battery (I need to have the input board done before I can put the batteries in the chassis). This is with the amp running and USB-C charger plugged in. Below, it is sending .18A to the batteries. The battery management will stop charging once the batteries are at about 12.5V. It drops the current as it gets closer to a full charge.
With the charger plugged in and batteries fully charged, it doesn't draw any power from the batteries.
At the moment, it negotiated 5V from the charger (source) and is boosting it to just above the battery voltage. If we wanted, we could source power so it could charge you phone too.
I'll do a drawdown test tomorrow to see how long it will run on a charge.
Overall, I'm very please with this amp. Kevin's amp design is fantastic. I've been listening to it for the last several hours with my SR-007's
-
18
-
-
Happy belated Birthday Kevin!
I hope you enjoyed the day
-
1
-
-
The board is two layers, but I had to use .5mm spacing for the USB. It also has a lot of 0402 components. I don’t think you could use a mill for the PD section. Also those USB and battery management chips were a nightmare.
It’s funny that after placing all those 0402 parts the 0603 stuff seems easy and the 0805 parts seem gigantic.
I used an oven to bake it since I was afraid the hot air station would blow those smaller parts away.
The DAC will use the XMOS input and will be on a separate board. We’ll have a version of the input board that is analog only.
-
1
-
-
I wanted to add my thanks here as well.
Greatly appreciated Todd!
-
1
-
-
Making some good progress on the amp...
I’ve got the USB-C PD all soldered on and ready for testing
Here’s the face plate with the jack
Here’s the amp assembled, but I still need to finish the power supply and amp sections of the main board
-
20
-
-
That looks beautiful!
-
Very glad it’s back and thank you!
-
1
-
-
Looks great!
So if I’m reading this right, more projects means more beer. That sounds right.
-
2
-
-
That's what I was thinking. If I used 1mm boards I think I would be fine.
The power supplies have parts only on one side, but the PD / battery mgmt needs parts on both sides. The cutouts would be easy enough.
I'm not sure what I'm going to do for the initial prototype. I'm pretty close with the current board and I may just build one. Seems like I should sleep on it
PS Interesting. Are you working on a balancer / protector or the management components?
-
I'm considering that. It would be nice to have one board for each component so they could be tested separately as well. Each supply, and the USB PD/battery mgmt could have separate boards. Everything else is DIY solderable and could go on the main board.
-
Making some progress on the main amp board. It will have a USB-C PD port so it will accept 5, 9, 15 & 20 volts. I think a 20W charger should be enough, but I'll have to test that once the prototype is built.
This is getting pretty dense. We'll have to have this partially assembled since the PD stuff is going to be a pain to do. There are 0402 components in addition to some of the larger chips with multiple pads under the chips.
This has 4 amp channels, +/-300V supplies, 580V bias and now the PD stuff with boost / buck on the input and includes the battery charging components as well. Looking at using 3S lithium batteries. The board is currently 161mm x 61mm and I think I can fit what's left.
There's still more to do, but here's where I'm at...
-
11
-
-
Ship in a bottle...
-
I use an oven (when it’s not too cold outside) and a hot air station during the winter.
I agree that you need to set the air velocity way down. I do keep a tweezers handy in case something moves or tombstones, but I generally don’t need it.
Try to have the air gun directly over and perpendicular to the parts. I move it around in small circular motions anywhere from 12mm - 25mm above the parts.
It’s very important that the parts are somewhat centered in the pads. For 0603 and down, I use a loop while I’m placing the parts.
Once you get the hang of it, it’s a very fast way of soldering.
-
1
-
-
Happy belated Birthday Doug. I hope you had s great day
-
1
-
-
They’re designed to sit flat on 75mm or taller heat sinks, so 2U will work just fine.
-
2
-
-
Work in progress...
I should be able to test soon 🤞
-
7
-
-
I hope you enjoyed your birthday Al
Happy Birthday!
-
1
-
-
I'm sure the A version of the BC556 should do just fine.
Just a note on the thermal grease. I've had issues with some types being conductive at 500+ volts - it's been years so I don't remember what I used. Make sure it doesn't get between the Aavid washer and the screw / ceramic insulator.
Looking good so far
-
1
-
-
Thanks Alan. I'll give that a read. Interesting that it's from back in the day
Here's a rendering of what the amp will look like.
It will be about 70 x 150 x 24 mm.
We're looking at using USB-C PD so we'll be able to run off of most chargers (at least 20W). Power input will have a boost/buck converter so it could run off of 5/9/15/20V chargers.
Still some work ahead, but we think we'll be able to fit a DAC in as well.
-
6
-
3
-
Ragnarok
in TV
Posted
I watched that about a year ago. It was only subtitles then.
I'm looking forward to season 2.