The Headcase Stax thread

[spritzer]

With no inside pics it is hard to tell but I had the Mk1 and it was utter trash and dangerous to the end user.  There are pics here somewhere of that but yeah, utter garbage

[K3cT]

23 hours ago, spritzer said:

With no inside pics it is hard to tell but I had the Mk1 and it was utter trash and dangerous to the end user.  There are pics here somewhere of that but yeah, utter garbage

Thanks, I would like to get into stats (particularly the CRBN) but it seems nicer if I can use my existing setup. 

[spritzer]

Good transformers are a great way to do that and are definitely getting more popular.  

[K3cT]

37 minutes ago, spritzer said:

Good transformers are a great way to do that and are definitely getting more popular.  

Yeah a couple of months ago I posted about the BHSE but unfortunately the seller went MIA so that didn’t work out lol.

I am a bit concerned my main amp, a SET 2A3 amp is a bit on the lower power side. In my experience it can drive the 32 Ohm transformer for RAAL Immanis fine but I don’t have much experience with e-stat interfaces. 

[spritzer]

2-3W or so?  That is very much on the low side but it always depends on overall system gain and how loud you listen.  A Stax SRD-7 Mk2 should work as the ratio on those is on the high side.  

[K3cT]

2 hours ago, spritzer said:

2-3W or so?  That is very much on the low side but it always depends on overall system gain and how loud you listen.  A Stax SRD-7 Mk2 should work as the ratio on those is on the high side.  

Yeah, around that range, if I'm not wrong it's about 2.5W into 32 Ohm load. I noticed that you have a Sansui variant of the SRD-7, will that work nicely as well?

[spritzer]

It should work, the ratio is a bit higher than the Stax ones.  Ultimately it's not about power but voltage in the system or voltage swing rather.  

[psyduck]

A closed back estat https://www.kaldasresearch.com/pages/inox

[Omega_ELS]

What do you think about these drivers?

can they have good sound?)

[chinsettawong]

They look nice!  I'm sure they can produce good sound.

[Milosz]

Hi all.  I've been trying to find measurements of electrostatic amplifiers - other sites typically don't know how to measure them- so looking for HD & IM distortion measurements, max voltage swing, SINAD, and also maybe slew rate.  I've spent some time looking around on this site but haven't stumbled across any yet... if someone could point me to a page here or maybe a site like Mjolnir or some other place that might list some measurements.  I just want to see what's considered good for electrostatic amps....

 

Thanks! 

[spritzer]

On 6/3/2026 at 7:26 AM, Milosz said:

Hi all.  I've been trying to find measurements of electrostatic amplifiers - other sites typically don't know how to measure them- so looking for HD & IM distortion measurements, max voltage swing, SINAD, and also maybe slew rate.  I've spent some time looking around on this site but haven't stumbled across any yet... if someone could point me to a page here or maybe a site like Mjolnir or some other place that might list some measurements.  I just want to see what's considered good for electrostatic amps....

 

Thanks! 

What the actual fuck is this?  How is posting in an open forum "reaching out to me"?  Copied from the Audioretards forum:

Quote

I've tried to contact Dr. Gilmore and his acolyte Spritzer of Molnir Audio to share with us their methods for measuring electrostatic amp performance, which is much different from the resistor-loaded method Amir used - but they are a clubby bunch and don't share much with mere hobbyists.

I know the testing requires a differential probe like the Tektronix THDP0100

I have a Carbon amp for my SR-007s, SR Lambdas, ESP950s and Dan Clark Corinas. Made a **HUGE** difference over the SRM-007 I used to use.

Did you send me a PM or an email?  No... so how did you reach out to me?  Go ask the retard in chief over there on how to test electrostatic amps... as he did such a good job last time.  Wasn't the quote something like, how can anybody listen to this as it measures so badly?  Yeah... stellar work there.  

Edited 1 hour ago by spritzer

[Milosz]

I wrote an email to you using [email protected]

[spritzer]

Which has probably been bounced back as that is not my domain name.  

[kevin gilmore]

miloz never contacted me. i would likely not respond if he did.

get one of each of these from ebay.

keithley 2015 6.5 digit thd multimeter and a hp 82357b (or later) usb to gpib adapter.

yes, the 82357b is a fake coming out the wrong end of the agilent factory (no shielding on the plastic) in china. but work absolutely identical to the real one which is about $600 new. unlikely to pass fcc radiated noise tests

and a windows 11 laptop.

then contact james king for the software package.

ebay price about $600 total for the 2 pieces.  (about $7k brand new)

have at it.  rated for 2000 volts peak to peak. no attenuators or other hacks needed. 

many of the used 2015 will require replacement of the display for about $75, and unsoldering about 100 connections. but the software does not require a well lit display except to put it into the right mode after you turn it on.

accurate to .002% Thd+N. built in balanced signal generator that matches the same specs. single box solution.

better than any stax amp with 50 to 60db of gain. the Noise component overwhelming the signal.

no way i would pay $35k for an audio precision and then pray that the required attenuator does not cause trouble. I would much rather pay that much for a set of CCB brakes and wheels.

retired 9 years now. i only do things that are fun.  like 30 to 130 in the Z06.  over and over and over. and yet no tickets (yet).

Edited 1 hour ago by kevin gilmore