GrindingThud

For headamp operation, is it recommended to put a relay delay on the output or is it stable enough during startup to not need that?

I was thinking three output jacks, one balanced and two SE.

Thanks!

Thanks! I think I'm going to attempt a 20V (21V) build and try to use the same PS from the KSA5. The boards are small enough I think it will package well. Which resistors get changed out?

This does look like a fun build. What's it swing VRMS?

Wife is grooving to the mix.... She sez mo sub bass

Is rum allowed in here?

Outstanding mix last week.....enjoying it now.

Wooga Wooga Wooga

Cool, mine was just over 110mv unmatched.

Very nice! I'm curious, after matching, what was your DC offset without the servo in?

Those look good!

Yum!

This little guy works great: http://www.lowes.com/pd_215726-20097-9302011_0__?productId=3339728&Ntt=shop+vac&pl=1&currentURL=%3FNtt%3Dshop%2Bvac&facetInfo= I use it to suck the bilge of my boat dry after races and other wet use. Small, easy to handle, and great suck. As for Hvac overflow. You should have two pipes. One from the condenser inside the unit to the outside world. If it gets plugged or the unit freezes up, water overflows to the pan. Pan should have a drain also. Use compressed air to blow out the clogged lines. Your garden hose from below should work also....just don't overflow back into the house. Orange is just mold goop....no biggie. A little bleach will tame that. The main thing is to make sure the heat exchanger pan drain is clear....it's most likely clogged at the trap at the air handler. DO NOT use drain cleaner...it will eat the aluminum heat exchanger.

Doh

http://www.alternesia.com/download.html

Got Snake?

Does that one have the vegan option? "It is like extra sound got delivered to me from heaven or from distant alien planet through warmhole" http://www.coconut-audio.com/xxx.html

I ate the whole bag.....I hope I'm not sorry:

That is good news! Now stop probing and get to listening.

Before you pull it apart, check the diodes at the input to the op amp (1N914 between the heat sinks). There are a number of resistors between your accidental short and the input/output. I doubt you fried a transistor. The diodes however.....zap, straight from V- to ground. I bet you fried that. Worth a look. Also, listen to it......scab some earbuds on it and hook up a sleazy input source.....you'll know if it's broke.

I'd push the rails to +/- 35 before going balanced. If a pair ever showed up at a meet we could bridge them.

I think fishski13 had some links earlier to photos of a single chassis build he did....could see a lot of the wiring. http://s23.photobucket.com/user/fishski13/media/012_zpsdfd46a29.jpg.html I can't believe you're not listening to it yet with just alligator clips. AC safety ground tied to enclosure - yepSignal input ground tied to enclosure through ground loop breaker (0.1uF X/Y-rated cap in parallel with 10 ohm 5W resistor)? - I floated mineInput RCA jacks isolated from enclosure - yepVolume pot tied to enclosure? - only by the mounting shaft on my ALPSOutput jack isolated from enclosure - yepOutput ground connected only to output jack, never connected to enclosure - yepDoes the 0V line from the PSU just float, or is it tied to the enclosure through a ground loop breaker? If not floating, can 0V line from PSU and input signal ground be tied to enclosure through the same ground loop breaker? - mine made noise when floatedShould output ground on the output jack be tied to the output ground on the amp board, or go directly back to the 0V line from the PSU? - I used the amp board, I've seen the other way like in the beta22...I think fishski13 did it that way.

PSU works fine with nothing attached. If it is the old one with early board runs....make sure you have the grounding error fixed discussed earlier in the thread.