wink

With the thread going all the way to the underside of the head certainly provides a weak spot for the head to separate from the thread. You'd think they'd leave a few threads width of bare shaft for extra strength.

ECQF6392JZ3: 0.0039uF 630V Polypropylene Film Capacitor (Radial Leads) Made By: PANASONIC Part Number: ECQF6392JZ3 $0.5000 Seeing as Mouser has only 1 3900pF 630V multi layer ceramic cap left, would this be a viable substitute for the TDK FK20C0G2J392J in the power Supply?

. x2 It would explain a lot.....

"Allied Electronics used to do this all the time though they just sent my packages to Israel. I mean IL and IS are pretty much the same thing... right? " Being part of the Stax Mafia, They should have sent it to Italy.....

On The preliminary BOM in the board buy thread there is a slight mistake in the spreadsheet for the KGSSHV power supply The BOM shows the 240K 2W resistors part No. 283-240K-RC as 2 per board. The quantity should be double i.e. 4 per board. Also, there are 4 0.1uF/1000V caps on the power supply board. Only 3 in the BOM. It also looks like there are 4 leds per amp board, and 3 listed on the BOM. D1, D2, D10 & D13.

My bad.

"and found a 3 inch long throw" Isn't this cone excursion, and not cone diameter?

One of the problems with tapping holes is the methodology. I usually turn the tap about 1 turn then retract half a turn to break the swarf. If you don't do this usually the tap gets stuck on the hole and sometimes breaks in the attempt to extract it. Some tips:- http://www.spaco.org/taptips.htm

I once had success with needle-nose pliers and worried the tap out, but the tap size was larger..

X2. As John said....

Happy Birthday,

That's made for fan cooling. You stick a fan on the end and blow air through the vanes. You'd tap the holes in the heatsink and screw the transistor onto the heatsink, using insulation as required.

2sa1968 from BDent showed up today. Look genuine.

. Did you buy any from them?

Probes: Have you considered a Fluke PM9100/101 High voltage probes with a 100:1 transfer ratio. Cable length 1.5 m. High input impedance (66,7 Mohm) and high isolation voltage of the tip allow measurements up to 1000 V CAT III or 4 kV on Type 1 circuits (Type 1 circuit has it's primary in installation category II). Equipped with command switch and range indicator (/191 only). Models: PM 9100/101 100:1, 200 MHz, 1.5 m, 66.7 MΩ / 3 pF, 1000 V CAT III **, Range 15 to 35 pF. PM 9100/191 100:1, 200 MHz, 1.5 m, 66.7 MΩ / 3 pF, 1000 V CAT III **, Range 15 to 35 pF, with Command Switch and Range Indicator. ** 1000 V CAT III or 4000 V type 1 circuit Each probe consists of: Probe cable assembly, Probe body, Retractable hook tip, Ground lead and clip, 6 colored identification rings. They're discontinued, but still available used.

. Thanks for the info. It saved me about $40.

"And even if you tell them the number of turns on the primary, and wire size, and the number of turns on the secondary and wire size, they insist on arguing with you. " That's because they're the ""experts""....

"Indubitably." And no doubt undoubtedly........

Sounds good..

Quote" red mallee knob in progress " Will they be too hot to handle on the T2?

Can't find the LSK389/2SK389's in the preliminary BOM......

"I have a quick group buy going here for the 10m90s if anyone is interested:" Missed it by ! ! that much......

Do you mean this bass.. http://www.google.com.au/imgres?q=bass&hl=en&sa=X&rlz=1R2ADRA_enAU443&biw=1280&bih=732&tbm=isch&tbnid=aMzJSvkU5iK_sM:&imgrefurl=http://new.dpi.vic.gov.au/fisheries/recreational-fishing/inland-angling-guide/fish-species/australian-bass&docid=iobr9LRk7eg5_M&w=675&h=346&ei=sA86TtzuNMrcmAWc9Ki6Bw&zoom=1&iact=rc&dur=422&page=2&tbnh=98&tbnw=192&start=18&ndsp=19&ved=1t:429,r:1,s:18&tx=88&ty=71 or this, http://www.google.com.au/imgres?q=bass&hl=en&sa=X&rlz=1R2ADRA_enAU443&tbm=isch&prmd=ivnsm&tbnid=jw-BNh8sflxuSM:&imgrefurl=http://profile.ultimate-guitar.com/aceandrew/pictures/personal/666024/&docid=RrU8ZdNPFKK8PM&w=745&h=274&ei=sA86TtzuNMrcmAWc9Ki6Bw&zoom=1&iact=hc&vpx=154&vpy=273&dur=78&hovh=136&hovw=371&tx=164&ty=90&page=1&tbnh=89&tbnw=243&start=0&ndsp=18&ved=1t:429,r:14,s:0&biw=1280&bih=732

DEOXIT PROGOLD CONTACT CLEANER & REJUVENATOR - AEROSOL Simple cleaners wash away dirt, grime, and dust from your expensive equipment but are often ineffective at cleaning tough oxidation and metal sulfide ... more... QTY 1+ $24.95 4+ $22.35 10+ $19.70 Enter Quantity From Jaycar

"I'd never seen deoxit in a spray bottle though! " Jaycar and Element 14 (Farnell ) sell it...