October 19, 201015 yr comment_396484 Does anyone have any idea of where to find some of these, or something else that would work for the same purpose, but with threads for screwing them to a bottom plate from the bottom? Home depot has those same tie downs. Report
October 19, 201015 yr comment_396486 I would have added this via edit, but not working correctly for some reason. At home depot, these are Gardner Bender mounting bases. Come in white or black. Report
October 19, 201015 yr comment_396488 Here, you have a 15 minute window after post creation to make any edits. Report
October 19, 201015 yr comment_396499 I would have added this via edit, but not working correctly for some reason. At home depot, these are Gardner Bender mounting bases. Come in white or black. But do the ones at home depot have threads? Report
October 19, 201015 yr comment_396517 Thanks for the edit tip. I did not know that. No, these do not have threads. I read the original post to say parts like those above or something similar but with threads. I now see it could have been read as only looking for those parts or similar but with threads. Report
October 19, 201015 yr comment_396525 How about using a nut and bolt on one of these? [ATTACH=CONFIG]3784[/ATTACH] Spectro Wire and Cable: Mounts for Cable Ties Report
October 25, 201015 yr comment_397910 Random q - Looking for stuff to fill my drawers with so I don't have to mail order parts every time I want to build something. Do these resistors look okay? Are they OEM for some real brand or are they just crap? 1/4W 0.25W 1% Metal Film Resistor Kit 2500pcs 50 values - eBay (item 260598923005 end time Nov-03-10 11:37:59 PDT) Report
October 25, 201015 yr comment_397981 I bought something similar a while back and I have no complaints. My Exstata uses these almost exclusively with no issues. Beats the hell out of paying 15cents for one generic resistor at the local store... Report
October 26, 201015 yr comment_398160 Cool, sounds good, since I guess I'm about to buy a bunch of 10pF and 100pF silver mica caps and probably some other goodies from the same seller. Report
October 26, 201015 yr comment_398197 Hehe crazy ideas like that means you end up with parts all over the place and you have no idea when you bought some of them.... Report
December 9, 201015 yr comment_409935 in your opinion, what's a reasonable connector to use with DSD and other serial audio signals. cat-5? Assume that the runs will be very short, and proper precautions are taken on each end of the connector. Report
December 9, 201015 yr comment_409951 and one more question... how the hell do you know how far off the PCB the center of the large mounting hole is for these? Neutrik - Audio - A Series - NC3MAH-0 I suppose you have to load the DXF file? bah. I don't have a way to do that... Report
December 9, 201015 yr Author comment_409955 I can help with the dxf if you can wait a few days. Report
December 9, 201015 yr comment_409964 I can help with the dxf if you can wait a few days. sure. seriously though, I cannot believe that dimension isn't on the PDF. how lame. Report
December 9, 201015 yr Author comment_409978 I also need to order a few resistors, if I can get my act together... Report
December 9, 201015 yr comment_409987 sure. seriously though, I cannot believe that dimension isn't on the PDF. how lame. It looks like 12.5mm to me ... Report
December 9, 201015 yr comment_410011 It looks like 12.5mm to me ... I'm pretty sure that dimension is just the distance from the center to the outer edge of the mounting hole. If you then look at the far left diagram, the PCB seating plane looks higher than that. Report
December 9, 201015 yr comment_410022 The mounting hole has depth, so unless you are cutting a gouge in the PCB to accommodate it, then the board can't be any higher. Also there are some little feet on the other side that are at the same level as the edge of the mounting hole. Report
December 10, 201015 yr comment_410048 those feet run the whole way front to back on both sides the lower mounting hole overlaps the PCB by a bit If you print it you could measure it, wouldnt have to be 1:1 either, plently of dimensions there Report
December 10, 201015 yr comment_410053 got up off my ass and did it my guess is 8.26mm to pin 3 2.32mm from the pcb top to the lower mounting hole and 9.80 from the lower hole to the middle of the 22mm cut out so 12.1mm from the PCB to the middle of the 22mm cutout how precise do you need it? Report
December 19, 201015 yr comment_412192 Canare L-4E6S/Belden 1694a/Mogami 2368 are they all about equal as far as RFI/EMI rejection goes? Report
December 20, 201015 yr comment_412618 Looking for a latching, pushbutton power switch akin to a Bulgin vandal resistant switch that can handle 3A at 125VAC for a gainclone. Edited December 20, 201015 yr by Emooze Report
December 20, 201015 yr comment_412620 Looking for a latching, pushbutton power switch akin to a Bulgin vandal resistant switch that can handle 3A at 125VAC for a gainclone. That's some gainclone. Perhaps the current on the primary in reality is a bit less? Report
December 20, 201015 yr comment_412624 I have no idea what the actual current is and my meter is at school. Just went off of the fuse rating. Report
December 20, 201015 yr comment_412671 I have no idea what the actual current is and my meter is at school. Just went off of the fuse rating. How did you come up with the fuse rating? Report
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.