Leaderboard

I found out that I have made it to the next round, for that IT director position. Interview on Thursday the 20th. I'm excited!

Rosemary, Cayenne, Balsamic, Ale Glazed Bone in Pork Chop and sautéed spinach. Sent from my iPhone using Tapatalk

Well, decided to terminate my contact after the inspection. Did lose some time and money but thinks its the right decision. There will be cool houses in the future.

Finished up the separate "Universal" PS that will be used to power my GG. Maybe try it with a Carbon later. Measurements: GRHV+: 404.5VDC GRHV-: -406.4VDC GRLV+: 15.01VDC GRLV-: -15.00VDC Pro Bias: settles at 580VDC Casework by Head-Case member joehpj Awaiting select parts on a slow boat from China to finish up the GG.

Tasty "tatties" To go with something else suitable for a hot evening

I call it Three Rib-Eye Pie. In truth, I just seasoned them this way and then grilled them. I was hungry and had people waiting so I didn't take after pics. Tasty, though.

That's too bad, Shelly. When we had the inspection done on our house, the inspector was literally laughing during the process. He thought nobody would be dumb enough to buy a house that needed so much work. But he had not met the likes of us! We managed to get the seller to do $35K worth or maintenance - basically everything significant mentioned in the report. I think the agents on both sides were shocked that he agreed to it.

simplified schematic just updated, I got the current sources flipped. when put in the test position, it puts fixed resistors to the plates of the tubes to -15 so then you adjust the main offset and differential. then move back to the on position and further adjust the servo pots. when working right, keeps the outputs to less than 100mv. but range is very tight.

Nice hike at Hawk Mountain in PA, while the hike was listed as hard I was not expecting the intense scrambles that lasted for seemed like about a mile. The view at the top was worth it!

Burgers. I derped when making the buns, but they still tasted good. I need to use my grinder more often, the fresh beef was delicious. https://imgur.com/a/og41c

Sorry guys! Today was a bit of craziness - trying to get all the finances in order as I wasn't expecting to do this, and certainly not this quickly! I thought I posted here but I guess not. The inspection is tomorrow at 1pm. Hopefully all goes well. If so, the closing is on August 15. Yikes!

Tickets procured. Anyone want to come?

I read the inspection report and I think she made the correct decision, all things considered.

Very slowly coming along... just noting the size difference. What is everyone using for the right angle headers? I bought some 4 pin headers for the main 4 pins but ground pin is off to the side, maybe just airwire that one? Also are you socketing the headers or directly soldering? If socketing what are you using?

Cosmic eggplant ftw

Very nice addition to a retro-cool system. I would think that a little more spread on those speakers would be an improvement in stereo imaging though.

Thanks for all the great info. in the previous comments. I just purchased an M-22 a short while ago and did a fairly extensive rebuild myself. I replaced all the Electrolytic Caps and burnished the contacts on all the relays. During the process I accidentally popped/shorted one of the output transistors and had to source a replacement. Once I got the replacement, I re-seated all the main transistors and added new thermal compound and adjusted the idle current and output. The power section of one of the boards gets quite hot so I replaced the Diodes and Ceramic caps there leaving additional space for air flow. Lastly, I added larger rubber mounting feet for air flow and cable routing.

Thanks gyus. Cheers *Loins of cod, blood sausage, chorizo, peppers, onion olives and a bed potatoes :-)

Keep 'em coming, Dusty... I'm writing all these metal bands down, stoner or otherwise, somewhere to check out later. Also reminds me to finally sit down and listen to the (no longer) new Gojira album.

Flank steak with chimichurri and veg