Leaderboard

Sorry guys! Today was a bit of craziness - trying to get all the finances in order as I wasn't expecting to do this, and certainly not this quickly! I thought I posted here but I guess not. The inspection is tomorrow at 1pm. Hopefully all goes well. If so, the closing is on August 15. Yikes!

power jumper block cleaned of all the epoxy j1,j3,j4 for 100v remove all others j2 j3 j5 for 120v remove all others j5,j6 for 240v remove all others and servo board pictures, unnecessarily complex tube rollers are going to have a lot of trouble with this, the servo has a pretty limited range, and the Russian similar's definitely will not work

here you go, a whole bunch of resistors are the wrong values, when I have time Power supplies are 350v t8000schem.PDF

The offer was accepted but Facebook got the scoop before us. Sad.

Thanks... Gonna populate the boards and mount the heatsink angle brackets this weekend. I've got to get going on these projects. They not gonna build themselves

Made an offer on this place. Went to visit it and fell in love with it and it's in a great location. The kitchen is amazing - a cook's dream - the island is the size of a bed. High ceilings on each floor, quartz countertops, walnut cabinetry, Bertazzoni gas cooktop/oven, tons of storage, and a really great "gameroom" with a room deck off of it, to use as an office. Feeling excited and nervous! http://www.har.com/2640-westgate-st/sale_71844848

Have a phenomenal day! I hope you don't have to bake your own Birthday cake.

Happy birthday!

Cheers Mike! - Happy Birthday

Eric Burdon is definitely one of the great rock and roll voices!

If the title of this thread had one more L in it, we'd be having very different discussions!

happy birthday mike!

Happy Birthday Mikey!!!!

just return it unopened

Thanks all! Dinner was a cooked chicken from Whole Foods. Perfect. Sent from my iPhone using Tapatalk

This is it....

Happy Birthday!

I hope you had Raffy prepare you a fantastic Birthday meal, with cake!

Congrats!

Fantastic!

Great news! Hope you are very happy there, Shelly.

Hurray Shelly! That place looks awesome.

#goodnews, #sad

Good luck with the offer, Shelly. That place looks great. Are you getting a piano too?

next to the transformer is 7815,7915 which makes +/-15 to the slot and also the servo board filaments are DC HV is unregulated Cap,100 ohm resistor,Cap servo pretty much identical to the T2 servo the 15k resistors are something else

I did this yesterday...

Various Artists – Ninja Cuts: flexistentialism

2sc6127 for the outputs and the voltage gain stage, resistors, for pull up on the voltage gain stage, darlington output need better picture of servo, so that one later, stacked ksa1156 for the tube drive, the rest of it is a modern 717 with available parts. wiring, 100v J1,J3,J4 120v J2,J3,J5

And you guys thought my lesbian jokes had gone too far! Shelly, I already have some good ideas. I'll be there when you're ready.

Trying to decide if they've jumped the shark.

Vinyl, special edition Remaster.

V20 ordered should have it early next week. Sent from my iPhone using Tapatalk

I believe that's, "kings of off-topic". This is actually atypically close to on-topic for us.

One note, it's a bad idea to twist the output wires on any electrostatic amp. This adds to the over all system capacitance which is bad.

Absolute madness close to being completed. A fully balanced phono stage, Erno Borbely design that appeared a couple of years ago in Linear audio. Three 19" rack width units. Two independent power supplies in one chassis, Left in another and right in another both fed from shunt regulators. Pass the medication....

You wanna circlotron? This is a circlotron... ... just where I live.

Not many houses have the the square footage for the circlotron.